Take two blue wires on the Nautilus wiring loom and connect them to two old wires horns. Fittings s

How to change the game in NCAA Basketball 10 for PS3? Spot clean the floor on a regular basis. How to Make Necklaces Out of Acrylic Tiles How to determine the age of an oil lamp How to fish bass from sliding sinker How to install Electro Signal Lab 445CRT How to fix machined Lip How to analyze a balance for beginners How to troubleshoot when the water is Soapy After Ri How to organize the pictures behind the couch
FJR1300 Nautilus compact horn is manufactured by Stebel. nylon line Horn consists of air hose and compressor horn small, generally designed to fit on any motorcycle and ATV many. Sound dynamics nylon line Nautilus compact horn and a loud, piercing great that exceeds the corners of the membrane action. With ease of installation and wiring loom supplied, every do-it-yourself repair person can install nylon line Nautilus compact horn of your motorcycle or ATV.
Place the support of the motorcycle or ATV gear to put and remove the key. Access to the battery box, raising the seat onto the hinge pins and remove the battery box with a screwdriver. It uses socket and wrench to loosen and remove the negative battery cable. Move to the front of the motorcycle (or ATV) and find the corner of the shares, are usually located in the vicinity of the fork tubes or frame downdraft. Size of the new Nautilus horn against the corner of the state with the opening of the tube Nautilus tube down and slightly to the rear of the bike.
Examine the stock horn mounting hole in order to determine whether the horn Nautilus fit in this place. Pull one or two wires from the horn stock, then remove the screw (or bolt) with a socket or screwdriver. If the stock horn has a small angle bracket attached to it move the handle nylon line to the corner of Nautilus and tighten the screws with socket nylon line or screwdriver. Place Nautilus horn on the frame and insert the mounting screw from the handle to the frame. Tighten the horn in place with socket or screwdriver.
Cut a piece of perforated aluminum strip with a pair of scissors nylon line to the desired length of tin to join the new horn to the alternative, the old horn mounting surface, if the existing horn bracket nylon line will not accommodate the new horn. Find a good source of a frame, or on a fork tree upper engine mount or on the radiator mounting bolts.
Attach the bracket to the aluminum strip frame Nautilus horn screw and tighten it with a socket and wrench to the frame. Tilt the corner of the opening to the bottom and slightly inclined to the rear of the motorcycle horn pipe by loosening the screw rotating, moving in the corner, and then tighten it with a screwdriver.
Take two blue wires on the Nautilus wiring loom and connect them to two old wires horns. Fittings shall be push-on blade types or bullet-type connector. nylon line Use wire strippers to cut off the ends of the old horn wires, strip them, and then fastening nylon line the connector needed. If you only have one wire from the old horn, protect other blue wire loom to the horn fastening screw to serve as a basis. Use a mesh plug in the set and cut and strip the end of the blue wire. Crimp eyelet at the end of the blue wire with wire strippers.
The red wire (from the same end of the beam) to the + terminal on the compressor nylon line and the horn wire to the black terminal - the compressor. They are both flat connectors and connector will fit exactly. Look at the wires on the other side of the loom. Take the black wire and redirect to the negative nylon line terminal of the battery. Remove the terminal nut is small eyelet screws and tighten with the socket.
Press the red connector knife that has a fuse connected nylon line to it to the top terminal of the relay. Run the other end of the same cable to the + terminal of the battery. Remove the nut to cinch the battery and install the red wire mesh on it. Tighten the cinch socket.
Connect the blue wire from the loom to the next post down the relay by moving the blade connector on it. Next post down the relay receives the red wire from the loom and the last post on the relay, the recent blue wire. Temporarily connect the negative battery cable to the battery and check the corner. If it works, use astringent tape supplied to secure the wires to the vehicle frame, tucking them carefully. If you do not have the sound of the horn, recheck your configuration connections and try again.
This work is licensed under a Creative Commons Attribution 3.0 Unported License. nylon line Google